Ai Area Lights

Four Ai Area Lights pointing through the windows

 

A common method for lighting an interior is to place area lights outside of the windows pointing into the room. Care must be taken with the size and position of the lights. If the lights are too close to the window frame it can cause areas near the windows to appear bleached out (see tone mapping below). A light sample value of 3 has been used in all of the example images.

Remember that you can also combine a directional light with the quad window area lights to achieve a similar effect as the skydome light.

  • Create four Ai Area lights and position them outside of the windows as indicated in the below left image. The settings used for the four area lights in the scene are below. The Exposure has been increased to 18, the Light Shape has been set to quad and the Samples have been increased to 3 for final scene rendering.

Ai Area light shape set to 'Quad'

With windows that contain glass, the area lights should be placed in front of the glass so that Arnold does not need to deal with glass intersections.  However, if the window is oddly shaped, then placing it right behind the window, so that the entire window is covered by the quad light would be the next easier option.

Indirect Diffuse Ray Depth

Light in real life will bounce around much more in an interior scene than it would in an exterior scene, therefore, you should increase this value if you wish to get more secondary bounce lighting into the scene. 

The images below show the effect of increasing the Indirect Diffuse ray depth in the Render Settings. Note that render times will linearly increase with regards to the number of bounces.

Sampling Noise

It is quite common to get noise when rendering interiors. This can either be due to lights not having enough samples or because the Gi Diffuse Rays are not high enough.

Setting Gi Diffuse Rays to zero allows us to focus our attention on the light samples. In the images below, shadow noise is clearly visible in the corner of the room. Increasing the light samples incrementally allows us to improve the shadow quality whilst keeping render times low. Increasing the lights Samples to is enough to sufficiently reduce the amount of shadow noise.

Diffuse Samples

Once we have fine tuned our light samples we can focus on Gi Diffuse noise. In this case increasing the Gi Diffuse samples to 5 provides a clean solution.

Area Light Samples

The example images below, compare the difference between rendering one large area light, two area lights and four area lights.

For each light Arnold is tracing nine rays (thirty-six in total with four lights), versus nine for just one light. Therefore more smaller lights will take longer to render than one large light. However, even though the number of light samples is the same (in this case three), there is more noise using just one large area light. This is more evident in the area around the bookcase.

Light Decay filter

Near Attenuation

The areas around the windows are very bright and bleached out. One way to fix this is using tone mapping (see below). The other is to use a Light Decay filter.

  • Connect one Light Decay filter to all four Ai Area Lights. With this filter it is possible to control the falloff of the light using the Use Near Attenuation attributes. In the below right image the Near Start is set to 40 and Near End is set to 200. You can see that the area on the floor near the lights is far less blown out when compared to the render that has no 'Light Decay' filter (GI Diffuse has been set to 0 in order to better see the effect).
Far Attenuation

The 'Far Attenuation' attributes work like a normal decay, however you can specify the start and end distance. This can give you more control over how much light fills the room by setting an 'end' distance. A simple interior scene below shows the effect of changing the 'Far End' attribute of the Light Decay filter. Note the effect it has on the floor's specular reflection.

 

ToneMapping  

An easy way to fix the bleached out areas around the window is to 'tone map' the image using post processing software.

  • Render the scene as a 32-bit EXR file. This will give you enough tonal range to play with in post.

 

Area Lights with HDRI 

We could do with adding some more natural looking colored light into the room. We can do this by using a HDRI in combination with an Area light.

Decreasing the intensity of the light until it is within a normal range should be sufficient to see the effect of the HDRI. However, it can be difficult to tell if the texture map has been mapped correctly to the light. In order to better visualise the effect, we can create a reflective sphere and place it in front of the window. This way we can see the HDRI reflected in the sphere. 

 

  • Create a sphere and assign an Ai Standard material. Reduce the Diffuse Weight to 0, increase the Specular Weight to 1 and decrease the Specular Roughness to 0. Render the sphere in the scene. You should see the HDR reflected in the sphere as in the image below right.

It is not possible to make Arnold lights visible to the camera. However, the Ai Mesh Light does have a 'Light Visible' option. 

Mesh light (poly plane) with 'Light Visible' enabled

 

 

  • No labels