Polygon plane with brick displacement texture assigned to it (rollover image).


Displacement maps can be an excellent tool for adding surface detail that would take far too long using regular modeling methods. Displacement mapping differs from bump mapping in that it actually alters the geometry, and therefore will have a correct silhouette, and self-shadowing effects. Depending on the type of input, the displacement can occur in two ways: Float, RGB & RGBA inputs will displace along the normal while a vector input will displace along the vector.

The example above shows how a simple plane, with the addition of a displacement map, can produce an interesting looking simple scene. The yellow toy appears to be hiding between the bricks, but we didn't have to model the bricks. They were produced simply by using a brick texture image as a displacement map by applying it to the displacement node.

You should ensure that your base mesh geometry has a sufficient number of polygons otherwise subtle differences can occur between the displaced low resolution geometry and the high resolution mesh from which it was generated.

Make sure that you use a 32bit or 16bit floating-point format to store your image, and not an integer format. An integer format will not work correctly. This is because integer formats do not support negative pixel values, which are used by floating-point displacement maps.

A video that demonstrates displacement workflow in the Arnold Shader Network editor can be found here. A video that demonstrates displacement production workflow examples can also be found here.

A tutorial that demonstrates displacement mapping using the <udim> token can be found here.


You must add an Arnold Tag to the geometry that you wish to displace in order to edit its subdivision and displacement attributes:


Arnold Tag showing Arnold displacement and subdivision attributes


Always ensure that you use the highest quality texture maps for displacement mapping. Arnold works well with very high resolution maps, as long as the maps have been pre-processed with the maketx utility. It will convert them into .tx files (which are tiled, mipmapped files). See the pages about the maketx utility and .tx files.



Subdivision Iterations set to 8. Subdivision Type set to Cat Clark.


Changing the Subdivision Type to either Catclark or Linear subdivision rules and increasing the iterations will improve the displacement quality. In this example the Subdivison Iterations have been increased to 8.

You must be careful when increasing the number of subdivision iterations (each iteration quadruples the geometry). This subdivision happens at render time, whenever a ray hits the bound box of the object. This is a better choice compared to increasing the subdivisions of the mesh within the DCC software (which will send the tessellated geometry to the renderer).

Per-Object Displacement Attributes

It is possible to set displacement settings on a per-face or per-object basis. However, any values that are entered in the Arnold attributes of the displacement node will override those settings. With multiple displacement shaders per object, and since an object can only have one value of Bounds Padding, Arnold takes the maximum value from all of them. Autobump poses the same problem as with padding, and so Arnold enables it if at least one of the displacement shaders has it enabled. 

Any changes to the displacement that are made on a mesh will modify the default displacement shader attributes. This may be useful in a scene that has two objects with the same shader but requires different shape displacement values. Another example would be an object that has more than one shader but requires two different Height values such as in the example below:

Same displacement shader assigned to two meshes, however, the mesh on the right has a per-object Height of 2


The per-object C4DtoA displacement attributes are divided into the following groups:


Controls the amount of displacement. Displacement height can have either positive or negative values. This attribute only applies with normal displacement. You can use this value to compensate for any inconsistencies between the exported displacement map and the low-resolution geometry.


Bounds Padding

Padding defines how much to extend the bounding box of the object, so that it can include any additional displacement coming from the displacement shader. When the bounding box is hit first by a ray, the displacement will be computed, so an unnecessarily high value will decrease the render efficiency. On the other hand, a low value could result in a clipping of the displaced mesh.

The proper workflow for displacement in Arnold is to have the shader give the final displacement value and then to offset the bounding box with the bounds padding attribute.

Below is another example of a situation where bounds padding is required. A checker texture is connected to a displacement shader that is assigned to a sphere. In the image on the left, parts of the render return black. This is because the Bounds padding needs to be increased for the displaced mesh. Increasing the Bounds padding to 3 fixes the problem. This effect may increase or decrease depending on the scale of the object that is being displaced and the amount of displacement used.



Scalar Zero Value

This is a floating point value which is applied as a shift to the displacement amount. It defines the value of the displacement map that is considered to be zero displacement. This value can vary depending on how the displacement map has been generated.


Autobump puts the high frequencies of a displacement map into the bump attribute so that you do not need as many Subdivision Iteration values. It is enabled by default in the Arnold attributes of the displacement node.

The autobump algorithm needs UV coordinates to compute surface tangents. Make sure your polymesh has a UV set applied.


Technical information:

When autobump is enabled, Arnold makes a copy of all of the vertices of a mesh prior to displacement (let's call that the "reference" mesh, or Pref). Prior to shading at some surface point on the displaced surface P, the equivalent Pref for that point is found on the non-displaced surface and the displacement shader is evaluated there (at Pref) to estimate what would be the equivalent normal at P if we had subdivided the polymesh at an insanely high tessellation rate.

The main difference between Arnold's autobump and using the displacement shader for bump mapping is that autobump has access to Pref whereas bump2d does not and would be executing the displacement shader on already-displaced points which could "compound" the displacement amounts.

The only extra storage is for copying P prior to displacement. There is no analysis of the displacement map; Arnold displaces vertices purely based on where they "land" in the displacement map (or procedural) regardless of whether it happens to "hit" a high-frequency spike or not.

Shader Displacement and Per-Object Displacement

Care should be taken when using both of these attributes at the same time. The relationship between the displacement shader and the per-object mesh displacement varies when rendering. These differences are as follows:


If the per-object Height value is increased when there is already some Displacement Scale it will have a multiplying effect on the displacement. For example, if the Displacement Scale is set to 0.1 in the shader and the per-object Height is increased from 1 to 2, the Displacement Scale will double in size to 0.2:

The effect of the Displacement Scale doubles from 0.1 to 0.2 when the mesh Displacement Height is set to 2.

Scalar Zero Value

If the per-object Scalar Zero Value is increased when there is already some Displacement Scale it will have an additive effect on the displacement. For example if the Scalar Zero Value is set to 0.2 in the shader and the per-object Scalar Zero Value is set to 200 cm, the Scalar Zero Value will double in size to 400 cm:

Auto Bump

If autobump in the displacement shader is enabled it will always be enabled. If autobump in the displacement shader is disabled, C4DtoA will read the shape autobump attribute and export that.


  • No labels